Jump to content

Recommended Posts

  • Legacy Donating Member
  • Member For: 10y 3m 16d
Posted
1 minute ago, arronm said:

Factory F6 turbo, engine has a lot of mods, will make 500 easy. E85 of course

Hmmmm ill be keen to see this result mate,

 

Though wouldnt it be better to get a new gtx gen 2 and not risk hurting the block?

 

Those new gen 2 76s will get 500rw and awesome spool everywhere.

Id have one if I was a months slower in buying the turbo I did

  • Legacy Donating Member
  • Member For: 11y 6m 5d
  • Gender: Not Telling
Posted (edited)

The block doesn't gaf. The compressor and iat are what matter in this case. 

 

Edit: I spose you meant rods.

Edited by Puffwagon
  • Dropping a turd
  • Legacy Donating Member
  • Member For: 18y 9m 7d
  • Gender: Male
  • Location: Perth
Posted (edited)

Hurt the block,    Engine is fully built, cosworth pistons , billet crank, etc.  Capable of lots of power

Edited by arronm
  • Legacy Donating Member
  • Member For: 10y 3m 16d
Posted
3 minutes ago, arronm said:

that's cause you been around for 9 months. More to it, than what you read.

Lots more to it,

Though over this 9mths ive been on here ive read over fark loads and leant a little...

Be great to see it work mate, just think there is a smarter solution for not a huge out lay

 

Cough gen 2 cough cough

  • Dropping a turd
  • Legacy Donating Member
  • Member For: 18y 9m 7d
  • Gender: Male
  • Location: Perth
Posted

True, but I want to take the factory turbo to the limit

  • Legacy Donating Member
  • Member For: 10y 3m 16d
Posted (edited)

U deep pocket short armed fark :pandalol:

 

Can we get a betting syndicate going on what it will make?

When is this tune happening?

I'll kick it off at 465rwkw @23.5psi  and pushing chit up hill hard from 5k rpm

Edited by BAXRTUTE
  • Dropping a turd
  • Legacy Donating Member
  • Member For: 18y 9m 7d
  • Gender: Male
  • Location: Perth
Posted

Yep, do that then move on..

 

Doubt many turbo falcons are making 400rwkw on 15psi on 98.. Shows the difference things like head work make. Lots and Lots of hours have gone into this engine.

  • Legacy Donating Member
  • Member For: 11y 6m 5d
  • Gender: Not Telling
Posted
Just now, arronm said:

True, but I want to take the factory turbo to the limit

 

Weld it shut. But why bother? 

 

You'll just have skids then high iat's, egt's and backpressure that a kiwi would envy. 

 

So far we've seen that it comes on slow in your current configuration despite lack of tune details. 

 

Fark it off and get something that has the right amount of lag to keep grip but can actually hold the mid and top end you desire.

  • Member
  • Member For: 11y 3m 27d
Posted
9 minutes ago, arronm said:

Hurt the block,    Engine is fully build, cosworth pistons , billet crank, etc.  Capable of lots of power

Nizpro Typhoons definitely did get the ton spent on them back in the day when they were intended to be exported to the UK.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...