Jump to content

Recommended Posts

  • ...JD TUNING ADELAIDE...
  • Legacy Donating Member
  • Member For: 18y 2m 3d
  • Gender: Male
  • Location: Adelaide
Posted

You guy's called for me ?

  • Like 4
  • Filthy weeb
  • Member
  • Member For: 13y 5m 18d
  • Gender: Male
Posted (edited)

No, butt out of it and stop plugging Jonny Tig.

Edited by stubbietubbie
FOR EMPHASIS, FOR CLARITY, FOR HONOUR
  • Legacy Donating Member
  • Member For: 10y 3m 16d
Posted

Did the Plugs 3 wks ago... 

Ive got a miss that wont go away, 

No codes... changed everything I can think of and no change!

Mainly happens under half throttle from 3k rev then kicks into gear, car shutters. Also happens sometimes at full throttle but not all the time. Been a head fark

  • ...JD TUNING ADELAIDE...
  • Legacy Donating Member
  • Member For: 18y 2m 3d
  • Gender: Male
  • Location: Adelaide
Posted

Check the wiring on the camshaft position sensor plugs ( back of engine left and right ) up top but just under the rocker cover area 

  • Like 1
  • Legacy Donating Member
  • Member For: 10y 3m 16d
Posted

Will do tomorrow chief, hope your right cause new coils, plugs, turbo intake alterations havent helped it.

Its like the turbo is starving of air, first thoughts was the under battery iintake but piping is fine. 

Just need to get my sh*t together and get a certain order happening and in the car

  • Member
  • Member For: 11y 3m 27d
Posted

Spent the morning fitting a new Venom bolt on cat section

(two piece for the BA /BF)

The bolts between the centre muffler and middle pipes were a bit of a struggle, but got there with a bit of raw grunt. Also put the cross over and pipes back on after installing new coils. 

Oil and filter next weekend then it's off to JD tuning for injectors and wastegate actuator upgrade.

  • Dropping a turd
  • Legacy Donating Member
  • Member For: 18y 9m 7d
  • Gender: Male
  • Location: Perth
Posted

Half way through mechatonics , seal change. But stopped for lunch.

  • The Toxic Rocket
  • Legacy Donating Member
  • Member For: 16y 3m 10d
  • Gender: Male
  • Location: Brisbane
Posted
On 21/07/2016 at 8:33 AM, JETURBO said:

Yeh I'm sure it was sold as a roller hey 

 

425 sounds about bang on for the stock turbo so good results, who tuned it ?


I bought it as a roller 2 years ago and we put it all the bits in it to get it going again.

Forced Performance Tuned it

  • Dropping a turd
  • Legacy Donating Member
  • Member For: 18y 9m 7d
  • Gender: Male
  • Location: Perth
Posted

Job done, test driven and back on the hoist to check for leaks in the morning..

  • Feeling the Love :-)
  • Legacy Donating Member
  • Member For: 13y 4m 3d
  • Gender: Male
  • Location: Not in Cairns anymore
Posted

did oil and filter this morning.

no hoist just 2 plastic ramps up front to allow this grumpy old man to get down and dirty.

1 hour start to finish (not bad for an old bastard) 

drove up the Karanda range to Mareeba to watch a round of the Aussie Supermoto champs.

I know it is a psychological thing, but the car always feels better with all that new oil goodness.  :thumbsup:

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...