Ralph Wiggum Moar Powar Babeh Legacy Donating Member 19,334 Member For: 20y 10m 5d Gender: Male Location: Perth Posted 04/06/17 03:48 AM Posted 04/06/17 03:48 AM Nah not the pump etc, just this bit thanks It will unclip from the hat and slide out
k31th less WHY; more WOT Site Developer 30,020 Member For: 18y 3m 18d Gender: Male Location: Melbourne Posted 04/06/17 03:52 AM Posted 04/06/17 03:52 AM ok, I'll see if I can get it out...
Ralph Wiggum Moar Powar Babeh Legacy Donating Member 19,334 Member For: 20y 10m 5d Gender: Male Location: Perth Posted 04/06/17 04:00 AM Posted 04/06/17 04:00 AM Cheers, it'll look more like this one with the four retaining clips, If you don't want the harness between the bulkhead and fuel pump I'll take that as well.
k31th less WHY; more WOT Site Developer 30,020 Member For: 18y 3m 18d Gender: Male Location: Melbourne Posted 04/06/17 04:18 AM Posted 04/06/17 04:18 AM OK. It was a bit of a pain to get out due to those 4 clips holding it in so strongly haha. Send me a PM with your postage details and I'll send it off to you.
Ralph Wiggum Moar Powar Babeh Legacy Donating Member 19,334 Member For: 20y 10m 5d Gender: Male Location: Perth Posted 04/06/17 04:46 AM Posted 04/06/17 04:46 AM Cheers mate, pm inbound.
NathanB Member 136 Member For: 13y 2m 3d Gender: Male Location: Melbourne Posted 04/06/17 05:51 AM Posted 04/06/17 05:51 AM Factory connector and vapour side wiring is good for 30amps. Chassis side wiring is not. I've seen substantial volt drop to high volume in tanks with stock chassis side wiring. I doubt it would be an issue with a 255 though. Yeah just curious as nizpro advised heavier wiring if doing an in tank 460. Just couldn't find info on he wore gauge used factory. Not a problem to replace but would rather not. I think a 255 will be fine now but in future it will supply an external surge and pump setup.
arronm Dropping a turd Legacy Donating Member 9,520 Member For: 18y 9m 1d Gender: Male Location: Perth Posted 04/06/17 07:00 AM Posted 04/06/17 07:00 AM It's simple to add a relay. Saves the possibility of volt drop 1
Box stock T. Member 1,384 Member For: 11y 3m 21d Posted 04/06/17 10:32 AM Posted 04/06/17 10:32 AM 7 hours ago, k31th said: fitted some wiper blades: no leaks from the fuel pump assembly after the first drive(s) after fitting It's fairly noisy good sign, imho. Then gave it a much needed wash as I hadn't done that for ages due to the amount of work I had to do to the car over the last weeks/months. Finally got a couple of side-on shots of the new brakes That XR6 badge on that side needs replacing haha. The "leak" wasn't fixed by the washer method :( will get the tuna to fix the leak, I think. Nice work Keith, the old red rocket is coming along nicely. I reckon a few people would have stock fuel pumps lying around place, I know I have one sitting on my bench in tge garage. Plus all other swapped out parts from my mods list. 1
bossmang FREAKY Legacy Donating Member 12,441 Member For: 16y 7m 3d Gender: Male Location: Melbourne Posted 04/06/17 10:45 AM Posted 04/06/17 10:45 AM sell the f6 to fund built motor and box for this red one keif 1
k31th less WHY; more WOT Site Developer 30,020 Member For: 18y 3m 18d Gender: Male Location: Melbourne Posted 04/06/17 11:10 AM Posted 04/06/17 11:10 AM haha no thanks, Freaky. Cheers Adam 1
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now