k31th less WHY; more WOT Site Developer 30,020 Member For: 18y 3m 18d Gender: Male Location: Melbourne Posted 03/06/17 01:51 PM Posted 03/06/17 01:51 PM any in-tank seems fine, from my experience, with the stock wiring setup. If you need more than an in-tank pump, then it gets complicated, wiring-wise. 1
Puffwagon Legacy Donating Member 16,348 Member For: 11y 5m 29d Gender: Not Telling Posted 04/06/17 12:04 AM Posted 04/06/17 12:04 AM You check how much amperage your pump will draw and if it exceeds the rating of the wire then you'll need thicker wire. Whether you need a relay or not depends on which wiring you are changing/upgrading.
Ralph Wiggum Moar Powar Babeh Legacy Donating Member 19,334 Member For: 20y 10m 5d Gender: Male Location: Perth Posted 04/06/17 01:08 AM Posted 04/06/17 01:08 AM Factory connector and vapour side wiring is good for 30amps. Chassis side wiring is not. I've seen substantial volt drop to high volume in tanks with stock chassis side wiring. I doubt it would be an issue with a 255 though. 1
k31th less WHY; more WOT Site Developer 30,020 Member For: 18y 3m 18d Gender: Male Location: Melbourne Posted 04/06/17 03:03 AM Posted 04/06/17 03:03 AM fitted some wiper blades: no leaks from the fuel pump assembly after the first drive(s) after fitting It's fairly noisy good sign, imho. Then gave it a much needed wash as I hadn't done that for ages due to the amount of work I had to do to the car over the last weeks/months. Finally got a couple of side-on shots of the new brakes That XR6 badge on that side needs replacing haha. The "leak" wasn't fixed by the washer method :( will get the tuna to fix the leak, I think. 1
Ralph Wiggum Moar Powar Babeh Legacy Donating Member 19,334 Member For: 20y 10m 5d Gender: Male Location: Perth Posted 04/06/17 03:11 AM Posted 04/06/17 03:11 AM What's happening with the old intank module kieth?
k31th less WHY; more WOT Site Developer 30,020 Member For: 18y 3m 18d Gender: Male Location: Melbourne Posted 04/06/17 03:13 AM Posted 04/06/17 03:13 AM (edited) good question... It's just in the box the new one came from, at the moment, after letting all of the fuel within it evaporate. what do you think I should do with it? edit: also got the stock catalytic convertor cut out and a 100cpi catalytic convertor + y-piece fitted the other day; also for the tune this week. Edited 04/06/17 03:38 AM by k31th
arronm Dropping a turd Legacy Donating Member 9,520 Member For: 18y 9m 1d Gender: Male Location: Perth Posted 04/06/17 03:37 AM Posted 04/06/17 03:37 AM (edited) Looking at the condition of it, 5c on ebay.... The issue with the high pots, is the lower the fuel gets the less effective they are. that's why I fitted my 460 to a factory pot. Edited 04/06/17 03:40 AM by arronm
k31th less WHY; more WOT Site Developer 30,020 Member For: 18y 3m 18d Gender: Male Location: Melbourne Posted 04/06/17 03:39 AM Posted 04/06/17 03:39 AM yeah, the bin was my thought, too.
Ralph Wiggum Moar Powar Babeh Legacy Donating Member 19,334 Member For: 20y 10m 5d Gender: Male Location: Perth Posted 04/06/17 03:42 AM Posted 04/06/17 03:42 AM I think you should remove the wiring connector from it and send it over this way.
k31th less WHY; more WOT Site Developer 30,020 Member For: 18y 3m 18d Gender: Male Location: Melbourne Posted 04/06/17 03:43 AM Posted 04/06/17 03:43 AM including the pump? if you want it, just pay for postage and I'll happily send it over to you.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now