bossmang FREAKY Legacy Donating Member 12,441 Member For: 16y 7m 8d Gender: Male Location: Melbourne Posted 25/05/17 11:07 AM Posted 25/05/17 11:07 AM its a track car everything will run hot hehehehe
arronm Dropping a turd Legacy Donating Member 9,520 Member For: 18y 9m 7d Gender: Male Location: Perth Posted 28/05/17 02:22 PM Posted 28/05/17 02:22 PM chasing a few more KW
k31th less WHY; more WOT Site Developer 30,020 Member For: 18y 3m 24d Gender: Male Location: Melbourne Posted 28/05/17 03:40 PM Posted 28/05/17 03:40 PM Replaced my turbo... Fitting this: Turbo out and looking at the exhaust housing: The reason the cheap CHRA failed almost immediately after fitting: The locking nuts and nordloc washers lined up: This is literally the first time I've used a gasket here And the studs, nuts and nordloc washers in place for turbo to manifold: And the same for the dump pipe The two turbo's side by side in "supercore" configuration: And all back together and ready to go back in the hole: Didn't take it for a drive as I was too dirty and it's likely to overboot and it's too late at night. Booked in for a tune on 7th June Might add injectors, fuel pump and punch the cat 1
skidxr6t skids Legacy Donating Member 2,754 Member For: 13y 7m 5d Gender: Not Telling Posted 28/05/17 10:54 PM Posted 28/05/17 10:54 PM take parts from f6 to make this one go faster? profit?? 3
arronm Dropping a turd Legacy Donating Member 9,520 Member For: 18y 9m 7d Gender: Male Location: Perth Posted 28/05/17 11:14 PM Posted 28/05/17 11:14 PM Is this the turbine housing you used to rebuild
k31th less WHY; more WOT Site Developer 30,020 Member For: 18y 3m 24d Gender: Male Location: Melbourne Posted 28/05/17 11:23 PM Posted 28/05/17 11:23 PM
arronm Dropping a turd Legacy Donating Member 9,520 Member For: 18y 9m 7d Gender: Male Location: Perth Posted 28/05/17 11:25 PM Posted 28/05/17 11:25 PM Didn't notice the cracks ???
k31th less WHY; more WOT Site Developer 30,020 Member For: 18y 3m 24d Gender: Male Location: Melbourne Posted 28/05/17 11:31 PM Posted 28/05/17 11:31 PM If you mean the little chips/scratches from the turbine blade hitting the housing, yes. If you're asking if this turbo needs to make a lot of PSI, then the answer is no. It'll be fine for the application.
arronm Dropping a turd Legacy Donating Member 9,520 Member For: 18y 9m 7d Gender: Male Location: Perth Posted 29/05/17 01:20 AM Posted 29/05/17 01:20 AM No the cracks st the bolt holes.
k31th less WHY; more WOT Site Developer 30,020 Member For: 18y 3m 24d Gender: Male Location: Melbourne Posted 29/05/17 01:24 AM Posted 29/05/17 01:24 AM there are no cracks at the bolt holes anyway, I'll keep an eye on the bolts loosening to see if there's a problem, but they certainly weren't loosening on the original 210,000km+ usage - they were tight as FARK haha
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now